Open

Congratulations on the purchase of your Secabo heat press!
Please read this operating manual carefully to ensure a smooth production launch with your
new device.
Any type of reproduction of this operating manual requires the written permission of Secabo
GmbH. Modifications to and errors in the technical data and/or product characteristics are
reserved.
Secabo GmbH accepts no liability for any direct or indirect damages resulting from the use
of this product.

Safety Precautions

Please read the information and safety precautions carefully prior to first commissioning of
the device!

• Never reach inside the heat press with your hands when it is connected to the power
  supply, especially if it is switched on and heated up – danger of burns!

• Never open the casing and do not make any modifications to the unit yourself.

• Should it be necessary to open the heat plate cover upon explicit request by
  Secabo's customer service team, it is recommended you wear respiratory protection
  and only touch the insulation wool located therein using gloves. Possible disposal of
  the insulation wool should only be done inside a closed bag.

• Ensure that neither liquids nor metal objects reach the inside of the heat press.

• Make sure you use a grounded wall socket. Keep in mind that a heat press may only
  be operated using a wall socket equipped with a ground fault circuit interrupter.

• Disconnect the heat press from the power supply when it's not in use.

• Always ensure that the heat press is out of reach of children during operation and
  never leave the device unsupervised when switched on.

• Make sure the unit is only used in dry rooms.

If you cannot comply with one or more of the aforementioned safety rules, or if you
are unsure as to whether you're in compliance with all of the points, please contact
our technical support.

Items included

Mechanical base of the heat press with heating element and base element	Open
Controller Box	Open
C13 Cold device cable	Open

Machine description

Open

a. Main switch (not shown)
b. Liquid Crystal Display (LCD)
c. Control panel with buttons and rotary push setter
d. IEC socket and ground connection controller (not shown), internal connections
e. Turning screws for adjusting the cylinder
f. Adjustable cylinder
g. Heating element cover and heating element
h. Press lever

Installation and commissioning

• Safely set up the TCB SMART heat press on a stable table.

• Position the controller box at the upper rear center of the base frame of the TCB
  SMART heat press and let the threaded bolts at the controller box slide into the slots
  at the base frame. Securely tighten the hand nuts.

Open

• Attach the small 6-pin plug from the rear side of the base frame to the appropriate
  socket on the outer right side of the controller box.

• Attach the large 5-pin plug from the surface of the heating element to the appropriate
  socket on the right outer side of the controller box.

Open

• Plug the PE conductor cable from the HPC01 Controller into the rear of the terminal
  at the base frame provided for this.

• Plug the supplied C13 cold device cable into the back of the controller box and
  connect it to a safety socket, which must be equipped with a grounded connection,
  protection via fuse and ground fault circuit interrupter.

The TCB SMART heat press is now ready for use.

Controller components and operation

Open

Display components and their meaning

Open

Open

 

 

 

 

 

Open

 

Area for time setting and countdown when press is closed

 

 

 

Area for time setting and activity indicator of the pre-press feature

 

 

 

 

Icon for the Bluetooth connection

 

General indicator for fault or error

 

Area for temperature indicator for target
temperature and actual
temperature

Indicator heat plate's heating active

 

Indicator press is done heating up

 

Indicator press is currently heating up or cooling down. Below the set temperature, the arrow is flashing upwards.

 

Indicator for management of memory slots

 

 

Counter for counting the performed press operations

How to use the controller

Initial setup when first switched on

When switching on the HPC01 controller for the first time, the language selection
appears. Select the appropriate language for you by turning the rotary knob to the
desired language and confirm by pressing.

Now select the desired unit for temperature - °C or °F - by turning the rotary knob to
the desired unit and confirm by pressing.

This initial setup will no longer be displayed when switching the transfer heat press
on in the future.

To reset the HPC01 controller to factory settings, simultaneously press the
button as well as the button for 3 seconds.

Setting the temperature

Briefly press , the symbol in the display begins to flash. The value in the
display changes from the current ACTUAL value to the TARGET value, which can
now be set. Turn clockwise to increase the TARGET temperature, counter-clockwise
to decrease. Press the rotary knob or press to store the set value. If no
input occurs for 5 seconds, input mode ends automatically. Pressing exits
input mode, the set value is not applied and the display returns to the current
ACTUAL value.

Temperature-related indicators

is activated whenever the heater is running.
During the warm-up phase, every 10s an estimated remaining warm-up time scrolls
across the display for 3s instead of the current temperature.

is activated when the actual temperature is equal to the target temperature,
with a certain deviation of less than +/- 3 °C.

Arrow up is activated when the temperature is rising (if below TARGET
temperature, arrow is blinking), arrow down is activated when the temperature is
dropping, e.g. during a transfer or if the heat plate is still hotter than the set target
temperature.

is generally activated in the event of faults or errors, and when there is a
significant deviation between TARGET and CURRENT temperature (value outside of
a range that allows for useful pressing).

Setting the time

Briefly press , symbol in the display flashes. Turning the rotary knob
clockwise increases time, counter-clockwise decreases. Press the rotary knob or
press to store value. If no input occurs for 5 seconds, input mode ends
automatically. Pressing will exit the input mode, the display will return to its
original value.

Configuring pre-pressing

Briefly pressing activates pre-pressing for the following press operation
using the preset time, and is deactivated again upon completing the press operation.
When activated, the Time + Pre symbols will light up in the lower part of the display
with the corresponding time indicator. This will count down to 0 while pressing,
whereupon the symbol and time switched off again.

Holding activates the setting mode for the PRE time analog with time
setting: Symbol in the display flashes. Turning the rotary knob clockwise increases
time, counter-clockwise decreases. Press the rotary knob or press to
store value. If no input occurs for 10 seconds, input mode ends automatically.
Pressing will exit the input mode, the display will return to its original value.

Pre-pressing can be activated permanently from the settings menu. More information
below.

Saving to and loading from memory slots

Press and hold rotary knob in the default state. flashes. The number
corresponding with the memory slot is shown below the save symbol. This indicator
rises by one when turning the rotary knob clockwise. Each stored temperature value
and time / PRE time value is also displayed at the top. If memory slot is blank,
dashes are displayed for temperature and time / PRE time.

To retrieve a stored value, confirm the selected value in the display by briefly
pressing the rotary knob. The stored values are now displayed, is deactivated
and no longer flashes.

To save the current values (to blank or currently used memory slots), first push and
hold the rotary knob ( flashes), then select the desired memory slot, then hold
the knob until the values and symbols flash briefly. The values are now both, saved
and loaded, no longer flashes, the memory mode has been exited.

Setting tier

Briefly press .

You generally navigate through the setting tiers according to the following scheme:

• Rotate knob - scroll through the settings.

• Press knob - dive into current setting.

• Rotate knob - choose values within the setting.

• Press knob - store value and exit from the setting.

• You may press to return to the parent tier if no action is to be taken
  in the subordinate tier.

The following eight menu items are available in the setting tier.

1. Auto Prepress

   • Enable / Disable a permanent pre-pressing.

2. Bluetooth

   • Enable / Disable Bluetooth.

3. Bluetooth PIN

   • You can use the rotary knob to save your individual PIN, which the app
     will then prompt you to enter. The default PIN from factory is 255,
     which is automatically recognized and used by the app.

4. Warning signal

   • Enable / Disable the warning signal before opening the press.

5. Sleep Mode

   • Setting the time interval in minutes, after which the press enters the
     Sleep Mode.

   • In addition, the temperature the press should be cooled down to when
     in Sleep Mode can also be set.

   • To completely disable Sleep Mode, set the time value to "0".

   • The active Sleep Mode can be exited at any time by pressing any
     button or by actuating the press lever. The press will then restore the
     previously set parameters.

6. Auto Off

   • Setting the time interval in minutes, after which the press completely
     turns off the heating.

   • To completely disable Auto Off Mode, set the time value to "0".

   • The active Auto Off Mode can be exited at any time by pressing any
     button or by actuating the press lever. The press will then restore the
     previously set parameters.

7. Language

   • Setting the menu language.

8. Unit

   • Configuring the temperature unit. Celsius or Fahrenheit are possible.

Resetting the counter

Open

Press the key for 2s, the display will briefly flash, then the counter is reset

Pair heat press with mobile device

• Press the key on the controller

• Enable Bluetooth:
  Use the wheel to scroll to the Bluetooth ON/OFF setting and press the wheel once.
  Now turn the wheel again to set Bluetooth to ON and confirm again by pressing the

  wheel.

• Setting the Bluetooth PIN:
  Use the wheel to scroll to the Bluetooth PIN setting and press the wheel once. Now
  turn the wheel again to set the desired Bluetooth PIN and confirm again by pressing
  the wheel. The default PIN is 255.

• Press the Settings button on the controller to exit the Settings menu
  
  

• Download the Secabo SMART Transfer App to your mobile phone and start it.

• The first time you start the app, you will receive a brief introduction that will help you
  understand the features and benefits of the app.

• After the introduction, a dialog opens, which will assist you with connecting the press
  to the app. The app automatically searches for Secabo SMART heat presses in the
  area. Please make sure that Bluetooth is activated on your smartphone.

• Simply select the respective heat press from the list to connect to it. If you have
  changed the Bluetooth PIN on the heat press, the app will prompt you to enter it in
  the app.

• The heat press is now connected and ready for use.

Please note that controlling your heat press via the Secabo SMART Transfer App is
only possible when the internet connection of the mobile device is active.

Controlling the heat press via Secabo SMART Transfer app

To learn how to control your Secabo TCB SMART heat press via the Secabo Smart Transfer
App, please refer to the app introduction as well as the help pages within the app.

Second setting tier for operational key figures and service

Press and hold the Settings button to enter the second tier of the settings. Here
you can retrieve helpful data and counter readings by turning the rotary knob.

Operation of the heat press

Performing transfers

• Turn on the heat press via the main switch.

• Define the desired temperature as well as time parameters and confirm them. The
  press then starts to heat up.

• Please refer to previous chapters to learn how to change the settings on the
  controller.

• Once the press has heated up, you can proceed with the first transfer. The clock
  starts counting as soon as the press is closed with the press lever.

• 3 seconds before the set time elapses, a warning signal is sounded (if activated in
  the settings), then the press opens automatically.

• You can end the pressing process before the set time has elapsed by pressing the
  button.

• You can adjust the contact pressure by turning the small hand screw at the bottom of
  the press to increase or decrease the distance the lever travels. Turning the knob
  clockwise increases the pressure, while turning it counterclockwise decreases it.

• Using the clamping lever at the left of the base element, fix the transfer object as firm
  and flat as possible to avoid wrinkling during transfer.

• No settings can be changed during the press operation.

• With each completed press operation, the value indicated by the counter increases
  by one, as soon as the specified time has fully elapsed.

Note: Please keep in mind that it takes some time for the press to cool off after it is
switched off. There is a danger of suffering burns until complete cooling.

Maintenance and cleaning

All maintenance work must be carried out with the press switched off and cooled off, no
exceptions! First, remove the plug from the wall socket. Only perform maintenance work
after consultation with our technical support team.

The press should be cleaned regularly using a soft cloth and a mild household cleaner to
remove adhesive residues, dust, etc. Do not use scouring sponges, solvents or gasoline!

Recommended times and temperatures

These values should only be considered as guideline values, may vary depending on the material
and must be checked before pressing.

Important note: You should perform your own tests with the respective transfer materials
and carrier media prior to each production. The aforementioned values, as well as any
manufacturer specification merely serve as indications. Washing resistance and behavior
during the transfer must be determined by performing your own tests.

No guarantee can be derived from the recommended values. It is always the user's
responsibility to determine and apply the correct settings for his specific conditions.

Note on garment finishing processes: After the press operation, garments must cool off
before any carrier media can be pulled off the transfer material. The hot glue in the transfer
material doesn't develop its adhesive strength until cooled off. If the glue does not stick in
its cold state, this may indicate that the pressing procedure was too cold or too short.

Technical data